 |
| Catagory: Adding-An-Amplifier |
Records 1 to 8 of 8 |
|
|
| The AOEM-xxx is a plug and play add-an-amplifier kit for factory amplified and non-amplified audio systems. When adding an amplifier in addition to a factory GM Delco/ Bose® or a Ford/ JBL amplifier the AOEM-kit takes out the guesswork. The OEM-1 gives you a fast and accurate installation without the need to cut wires or splice wires. |
|
|
|
|
|
|
|
|
| The C2A-CHY provides a 4-channel pre-amp output signal for use with aftermarket amplifiers. This interface uses the full range fixed level headunit output in conjunction with CAN-bus messages and delivers a 5v RMS (max) pre-amp output with fading and balancing capabilities. |
| • 4 channel output. • 5v RMS (max output). • Data controlled remote turn on wire. |
Compatible Vehicles:
2004-2007 Durango
2005-2007 300, Magnum, Dakota, Charger, Grand Cherokee, Commander
2006-2007 Caliber, Ram
2007 Compass, PT Cruiser, Aspen, Patriot
2008 Caliber, Compass, PT Cruiser, Ram
2006-2007 Mitsubishi Raider
The vehicle must be equipped with a factory installed amplifier. If the vehicle does not have a factory installed amplifier or if the amplifier has been disconnected from car, the AOEM-CHR2 must be used. |
|
Latest Revision: 1.4.4 |
|
|
|
|
|
| The C2A-CHY2 provides a 4-channel pre-amp output signal for use with aftermarket amplifiers. This interface uses the full range fixed level headunit output in conjunction with CAN-bus messages and delivers a 5v RMS (max) pre-amp output with fading and balancing capabilities. |
| • 4 channel output. • 5v RMS (max output). • Data controlled remote turn on wire. |
Compatible Vehicles:
2007-2008 Dodge Nitro, Jeep Wrangler
2008 Caravan, Town & Country, Liberty
The vehicle must be equipped with a factory installed amplifier. If the vehicle does not have a factory installed amplifier the AOEM-CHR3 must be used. |
|
|
|
|
|
|
| The C2A-CHY3 provides a 4-channel pre-amp output signal for use with aftermarket amplifiers. This interface uses the full range fixed level headunit output in conjunction with CAN-bus messages and delivers a 5v RMS (max) pre-amp output with fading and balancing capabilities. |
| • 4 channel output.
• 5v RMS (max output).
• Data controlled remote turn on wire. |
Compatible Vehicles:
2008 300
2008 Aspen
2007-2008 Avenger
2008 Charger
2008 Commander
2008 Dakota
2008 Durango
2008 Grand Cherokee
2007-2008 Sebring
2008 Challenger
The vehicle must be equipped with a factory installed amplifier. If the vehicle does not have a factory installed amplifier the AOEM-CHR3 must be used. |
|
|
|
|
|
|
| The C2A-GM24 allows you to add a 2 channel aftermarket amplifier for GM vehicles with Class 2 data bus. What makes the C2A-GM24 unique is that is takes the fixed level audio signal from the factory head unit before it gets to the Bose® amplifier and gives you a variable output. The C2A-GM24 outputs are digitally controlled by the headunit's volume knob. You get full range audio signal, not a Bose® specific equalized output. |
• 2 channel RCA outputs with left and right level adjustments
• User selectable front fade, rear fade or non-fading output.
• +12volt remote turn-on output.
• Plug & Play, no hard wiring required. |
Vehicle application:
2003-2004 Trail Blazer LT, Trail Blazer LTZ, Envoy SLT
2003-2006 Escalade (all), Sierra Denali, Yukon Denali
2003(only) Hummer H2
The C2A-GM24 does not replace the factory amplifier. If the factory amplifier is removed or disconnected, the C2A-GM24 will not function.
|
|
Latest Revision: 1.4.18 |
|
|
|
|
|
| SNI-15 converts 10 to 30 watts per channel speaker level output into a pre-amp signal. Perfect when adding an amplifier to a factory or aftermarket radio. Great for getting an additional set of pre-amps outputs from a head unit equipped with only one set. |
• Fixed 10:1 conversion.
• Linear from 20-20,000Hz at +/- 5 dB, while maintaining signal phase.
• Isolates input and output circuits to prevent ground loop noise. |
White: Left(+) speaker
White/Black: Left(-) speaker
Grey: Right(+) speaker
Grey/Black: Right(-) speaker |
|
|
|
|
|
|
| SNI-35 converts 2 to 40 watts per channel speaker level output into a pre-amp signal. Perfect when adding an amplifier to a factory or aftermarket radio. Great for getting an additional set of pre-amps outputs from a head unit equipped with only one set. |
• Fixed 10:1 conversion.
• Linear from 20-20,000Hz at +/- 5 dB, while maintaining signal phase.
• Isolates input and output circuits to prevent ground loop noise. |
White: Left(+) speaker
White/Black: Left(-) speaker
Grey: Right(+) speaker
Grey/Black: Right(-) speaker |
|
|
|
|
|
|
| The Trunk-LOC is the same as the SNI-35 below but with a low voltage trigger built into it.
The low voltage circuit senses voltages as low as 0.8 volts and gives you a 12 volt output with a one second delay. |
• Trigger off of speaker leads or +5 volt remote wires.
• Remote turn on for aftermarket amplifiers in vehicles without a factory remote wire.
• Eliminates turn on pops in amplifiers. |
|
|
|
|
|
|
|
| |
Pacific Accessory Corporation
1340 Ritchey St. • Santa Ana, CA 92705 • USA
Voice: (714)835-3022 • Fax: (714)835-3233
Copyright ©2009 PAC |
|
|
